Heavy Vehicles.

      Carrying the world on their shoulders

—Trucks, Busses and Coaches

    • Preventive Maintenance Inspections and Service Programs

    • High-Voltage and Low-Voltage System Inspections

    • High-Voltage Battery Pack Inspection and Condition Assessment

    • Battery Management System Testing and Validation

    • Insulation Resistance, IMD and RCD Testing and Validation

    • High-Voltage Interlock Loop and Safety Circuit Validation

    • Contactor, Pre-Charge and HV Distribution System Testing

    • Power Distribution Unit Inspection and Functional Testing

    • Grounding, Bonding and Equipotential Continuity Testing

    • Service Disconnect and HVIL Inspection

    • Thermal Management and Cooling System Inspection

    • Thermal Imaging, Heat-Loss Assessment and Thermal Budget Analysis

    • Charging System Inspection, including AC and DC Fast Charging

    • Wiring Harness, Connector and Signal Integrity Inspection

    • Post-Service Functional Testing and System Validation

    • Vehicle Commissioning, Recommissioning and Return-to-Service Support

    • Fleet Maintenance Planning and Technical Support

    • Technical Reporting, Service Documentation and Test Recordson text goes here

    • EV, PHEV, HEV and FCEV Fault Diagnosis and Repair

    • High-Voltage and Low-Voltage System Diagnostics and Repair

    • Battery Management System Fault Diagnosis

    • High-Voltage Battery Pack Fault Investigation and Repair

    • Cell, Module and Pack-Level Fault Investigation

    • Isolation Fault Location and Leakage Current Investigation

    • High-Voltage Interlock Loop Fault Diagnosis

    • Contactor, Pre-Charge and HV Distribution System Fault Diagnosis

    • Power Distribution Unit Diagnostics and Repair

    • DC-DC Converter, On-Board Charger and Charging System Diagnostics

    • Inverter, Motor Controller and Electric Drive System Diagnostics

    • Regenerative Braking and Brake-System Integration Fault Finding

    • Thermal Management and Cooling System Diagnostics and Repair

    • CAN Bus, LIN Bus and Vehicle Network Diagnostics

    • DTC Analysis, Live Data Monitoring and Root-Cause Investigation

    • Wiring Harness, Connector and Signal Integrity Fault Finding

    • AC and DC Charging Fault Diagnosis

    • Fuel Cell System Diagnostics and Balance-of-Plant Fault Finding

    • Hydrogen System Electrical and Control Diagnostics

    • Component Replacement, System Integration and Configuration

    • Software Configuration, Calibration and Diagnostic Support

    • Repeat-Failure Investigation and Root-Cause Analysis

    • On-Site Breakdown Support and Technical Troubleshooting

    • Post-Repair Functional Testing and System Validation

    • EV, HEV, PHEV and FCEV Conversion Design and Engineering

    • Complete Electric and Hybrid Powertrain Architecture Development

    • High-Voltage Battery Pack Design, Integration and Validation

    • Battery Management System Selection, Configuration and Integration

    • High-Voltage Power Distribution Unit Design and Build

    • Contactor, Pre-Charge, Fuse and Service Disconnect System Design

    • Electric Motor, Inverter and Transmission Integration

    • Gear Ratio, Performance, Range and Energy Consumption Modelling

    • Charging System Integration, including AC and DC Fast Charging

    • DC-DC Converter, On-Board Charger and Auxiliary System Integration

    • Thermal Management, Cooling Circuit and Heat-Rejection Design

    • Fuel Cell System and Balance-of-Plant Integration

    • Hydrogen-Electric Powertrain Control and Electrical Integration

    • High-Voltage and Low-Voltage Wiring Harness Design and Manufacture

    • CAN Bus Architecture, Gateway Development and Network Integration

    • Vehicle Control System Design, Programming and Calibration

    • OEM Component Integration and Reverse Engineering

    • Instrument Cluster, Driver Interface and Control Integration

    • Regenerative Braking and Brake-System Integration

    • Electrical Schematics, Harness Drawings and Technical Documentation

    • Component Selection, Sizing and Engineering Validation

    • Prototype Vehicle Design, Assembly and Commissioning

    • One-Off and Low-Volume Vehicle Builds

    • Classic, Commercial, Heavy-Vehicle and Specialist Vehicle Conversions

    • Motorsport, Off-Road and Special-Purpose Electrification Projects

    • Existing Conversion Review, Rectification and System Improvement

    • Design Verification, Testing and Validation Support

    • Compliance Documentation and Engineering Support

    • Production Readiness and Low-Volume Manufacturing Support

    • End-to-End Concept, Design, Build and Commissioning Services

Leave us a message to book in.

Bespoke Engineering.

Bespoke engineering, built from first principles.

From high-voltage architectures to complete vehicle systems, every solution is designed to suit the application—not forced to fit it. We develop, integrate, and validate complex electrical and mechanical systems for real-world performance, reliability, and compliance.

No templates. No shortcuts. Just engineered outcomes.

Mine Spec Hydrogen-EVs

Hydrogen-electric, mine-spec, built for the harshest environments.

This 52-seater coach combines Hydrogen fuel cell technology with a robust DANA Sumo HD electric drivetrain, a 141kWh LFP High voltage battery system from CATL - delivering zero-emission transport without compromising range, reliability, or uptime. Designed for heavy-duty operation(mining inclusive) , it integrates cutting edge energy management, ruggedized systems, and safety-first engineering—proving that clean transport can perform where it matters most.

Zero emissions. Full capability. No compromise.

Mobile EV Fast Charge HUB

Mobile energy, engineered without limits.

This heavy rigid EV truck integrates a high-capacity energy storage system, a high-efficiency turbocharged internal combustion range extender, and six CCS2 fast charge outlets—delivering rapid, reliable power wherever it’s needed. Built for peak demand scenarios, it bridges the gap between grid constraints and real-world energy needs.

Deployable power. Fast charge anywhere. No infrastructure required.

Electric Rear-loading refuse collection and compaction truck

Built for the toughest routes, engineered for a cleaner future.

This all-electric rear loader combines high-capacity energy storage with purpose-built compaction systems, delivering quiet, zero-emission waste collection without sacrificing performance or uptime. Designed with durability, serviceability, and operator efficiency at its core, it’s a workhorse redefined for modern cities.

Clean streets. Zero emissions. Built to work.